Unlike bisphenol-A epoxy resins, cycloaliphatic epoxies have electron-rich epoxy groups that react only with difficulty with nucleophiles. Steric hindrance makes it hard for a nucleophile to attack the carbon atom, and reactivity is far slower than that of terminal epoxy groups, so cycloaliphatic epoxy resins react poorly with amine and imidazole curing agents. With electrophiles, however, the situation reverses: the electrophile attacks the oxygen atom, where no steric hindrance exists, so cycloaliphatic epoxy resins readily react with polyhydric phenols, anhydrides and cationic curing agents.
Cationic curing systems
Mechanism: on heating, or after a photo-cationic initiator absorbs light and photolyses, a thermal cationic initiator generates a superacid (H⁺ / Lewis acid). This initiates ring-opening cationic polymerisation of epoxy and vinyl ether groups, forming an insoluble, infusible three-dimensional network, as shown in the reaction scheme.

The DSC curves below show the exotherms of cycloaliphatic epoxy resin with different thermal cationic initiators (Donghua Material Science products). DH080 and DH081 are hexafluoroantimonates and DH091 is a triflate; the reactivity ranking read from the curves is DH080 > DH081 > DH091.
DH080 and DH081 suit coatings, adhesives and composite systems that need rapid curing at low to medium temperature: reaction is fast and the pot life after mixing is longer, about 12 h at room temperature.
DH091 suits systems requiring latency, for medium- and high-temperature curing such as adhesives and prepregs.

As the next set of curves shows, the cycloaliphatic epoxy resin DE021E is more readily ring-opened by the protonic acid released from the cationic curing agent, so in the cure kinetics both the onset and peak reaction temperatures of DE021E/DH081 are far below those of 128/DH081: cationic curing proceeds more easily. Faster curing and higher line efficiency therefore become possible.

Cycloaliphatic epoxy resins are used not only in thermal cationic curing but widely in photo-cationic curing as well, where they cure rapidly and therefore serve as the base resin. Photo-cationic cycloaliphatic epoxy systems are today used in tinplate coatings, flexographic inks, glass varnishes, plastic varnishes and 3D printing.

As the RTIR conversion curves show, the cycloaliphatic epoxy group cures faster and to a higher conversion than conventional glycidyl ether epoxies. Photo-cationic systems offer the following advantages:
- No surface oxygen inhibition;
- Greater depth of cure than free-radical systems;
- No solvent and no hazardous emissions during cure, environmentally friendly;
- Low shrinkage and good adhesion to substrates;
- Excellent chemical resistance, including resistance to boiling water.
Curing with anhydrides
When epoxy resin is cured with an anhydride, the following reactions take place in the presence of an accelerator such as a tertiary amine or a quaternary ammonium salt:
(1) The anhydride reacts with the tertiary amine to form a carboxylate anion.

(2) The carboxylate anion ring-opens the epoxy group to form an oxyanion.

(3) The oxyanion reacts with the anhydride to form an ester structure.

The next figure compares the cure kinetics of the cycloaliphatic epoxy DE021E and the bisphenol-A epoxy 128 with methylhexahydrophthalic anhydride. With a suitable accelerator at a high loading (4% TEAB), the onset and peak reaction temperatures of DE021E with the anhydride are fairly close to those of the 128 resin.

Compared with amine curing agents, anhydride curing agents are less toxic and less volatile, but they still have some drawbacks:
- (1) Anhydrides readily absorb moisture from the air to form free acid, which affects both cure rate and the properties of the cured product.
- (2) The reactivity of anhydride with epoxy is comparatively low, so curing is slow and takes a long time.
- (3) The ratio of epoxy to anhydride must be calculated precisely on a stoichiometric basis.
Curing with amines
The final figure compares the cure kinetics of the cycloaliphatic epoxy DE021E and the bisphenol-A epoxy 128 with the cycloaliphatic amine 1,3-BAC. It is clear that, because of steric hindrance, the nucleophile struggles to attack the carbon atom: DE021E reacts with 1,3-BAC only with difficulty, and both its onset and peak reaction temperatures are far higher than those of 128 + 1,3-BAC.
