Amorphous alloys, also known as metallic glasses, are a new class of metallic materials produced by special processes such as rapid solidification, in which the atoms form a glassy structure that is disordered over long range and ordered only over short range. With high permeability and extremely low loss, they have become a replacement for silicon steel sheet in motor stators and rotor cores.
GAC Aion recently launched the world’s first new energy intelligent vehicle fitted with an amorphous motor. This not only marks the transition of amorphous alloys from the laboratory to volume application, but signals that the motor revolution driven by amorphous alloys is accelerating.

The special structure of amorphous motors and their high-frequency operation place extremely high demands on insulation materials. For amorphous insulating impregnating varnish, the core requirements can be summarised as follows:
- High-frequency heat resistance. Amorphous motors often run at high frequency, where high-frequency pulse voltages readily trigger discharge. The insulation system must offer excellent corona endurance, and the thermal class is usually required to be H or above (180–220 °C).
- Low stress, low shrinkage. Amorphous ribbon is extremely thin and brittle and is sensitive to mechanical stress, so the insulating material must have very low curing shrinkage to avoid distortion of the core’s magnetic circuit by stress.
- Excellent chemical resistance. In a hot oil environment the material must not hydrolyse or crack, and must not release small molecules, which would degrade insulation performance and cause powdering of the film.
- System compatibility. Coating, winding, impregnation and structural components must form a matched material system with compatible processes.
The insulating impregnating varnish solution combines cycloaliphatic epoxy resin with an anhydride system, drawing on the resin’s low viscosity, low shrinkage, high heat resistance and high insulation. The product has been successfully adapted to impregnating varnish applications and is tailored to the key characteristics of amorphous alloy motors, high-frequency operation, high magnetic flux density and a brittle core, with five core advantages that safeguard stable operation:
- Deep penetration. The resin system has low viscosity and good wetting, so it quickly penetrates between the amorphous alloy laminations and fills them completely, effectively reducing eddy current loss and improving motor efficiency.
- Low curing shrinkage. Volume change before and after cure is minimal, with shrinkage held below 2%, which prevents stress generated during cure from damaging the thin amorphous ribbon and preserves the integrity of the core structure.
- High heat resistance. The product has a high thermal class, with a glass transition temperature of up to 160 °C, so it withstands long-term high-temperature operation and eliminates insulation failure caused by heat ageing.
- Good chemical resistance. The cured system has a high crosslink density and outstanding corrosion resistance; it resists attack by different transmission oils at high temperature and significantly extends the service life of the motor insulation.
- Mechanical and adhesive performance. Even under complex and harsh conditions such as high/low temperature cycling, mechanical strength and bond strength are retained, ensuring that motor components stay firmly connected and overall reliability improves.
The measured performance of the product is shown in the table below. Every indicator is excellent, confirming the core advantages and providing solid data support for practical application.
| Test item | Result |
|---|---|
| Gel time at 140 °C | 20–22 min |
| Initial viscosity (cP) | 180–200 |
| Viscosity after 96 h at 60 °C (cP) | 480–520 |
| Tensile strength (MPa) | 55–60 |
| Tensile modulus (MPa) | 2,500–3,000 |
| Elongation at break (%) | 2%–3% |
| Flexural strength (MPa) | 100–120 |
| Flexural modulus (MPa) | 2,600–3,100 |
| Deflection (mm) | 5–10 |
| Tg (°C) | 160–170 |
| Curing shrinkage (%) | 2–2.5 |
The amorphous insulating impregnating varnish based on a cycloaliphatic epoxy/anhydride system precisely matches what amorphous alloy motors need, high frequency, high magnetic flux density, high heat resistance and complex operating conditions. It effectively improves insulation reliability, running stability and service life, and provides an outstanding insulation solution for the efficient, energy-saving and long-term safe operation of amorphous motors.
If you are looking for an impregnating varnish solution with high heat resistance, high chemical resistance, high insulation and low shrinkage, you are welcome to contact our technical team. Let the cycloaliphatic epoxy impregnating varnish solution help your products run more stably and efficiently.

