Coastal high-salt-fog exposure, saline-alkali tidal flats, long-term outdoor sunlight — composites serving long-term under such conditions need both weatherability and heat resistance. Conventional bisphenol-A epoxy resins fall short on weatherability and show obvious performance decay at high temperature; cycloaliphatic epoxy resins can address both shortcomings from their intrinsic characteristics, providing a fundamental solution for heat- and weather-resistant composite systems.
Intrinsic characteristics that break through operating-condition bottlenecks
Cycloaliphatic epoxy resins can simultaneously handle salt-fog ageing and high-temperature loading challenges. Compared with conventional epoxy resins they offer the following advantages:
(1) Higher glass transition temperature — Tg > 200 °C, which significantly improves the high-temperature performance of prepregs, adapts to long-term use under high-temperature conditions, and avoids deformation and performance decay caused by temperature changes.
(2) Room-temperature viscosity of only 200–300 cPs — right in the ideal window for pultrusion and filament winding. High Tg and easy processing are no longer an either/or choice.
Effect of different DE021E addition ratios on the Tg and viscosity of a conventional epoxy system
| DE021E addition ratio | Resin viscosity (cP) | Viscosity reduction | Tg (°C, DSC) | Tg increase |
|---|---|---|---|---|
| 0% | 13,860 | — | 129 | 0% |
| 10% | 8,882 | 36% | 142 | 10% |
| 30% | 2,982 | 78% | 153 | 19% |
| 40% | 2,156 | 84% | 159 | 23% |
| 50% | 1,648 | 88% | 166 | 29% |
| 70% | 650 | 95% | 172 | 33% |
| 80% | 478 | 97% | 178 | 38% |
| 100% | 235 | — | 208 | — |
(3) No benzene ring — weatherability is greatly improved, effectively resisting UV light, high/low-temperature shock and other environmental influences, resisting yellowing and ageing, and extending the service life of downstream products. It is particularly suitable for outdoor and long-service composite parts.
UV ageing test conditions: UVA artificial ageing, 8 h light / 4 h off to simulate the day–night cycle (ASTM G154 Cycle 1); 8 h irradiation at 60 °C and 0.76 W/cm² plus 4 h standing at 50 °C counts as one cycle.
(4) Extremely low halogen content and excellent insulation — total chlorine < 5 ppm, breakdown voltage up to 13 kV and partial discharge 1500 V, combining environmental compliance with high insulation for high-end composite applications in new energy and electrical/electronic engineering.
Putting cycloaliphatic epoxy to work in engineering applications
With these distinctive properties, cycloaliphatic epoxy resins handle complex service environments such as high salt fog and high temperature with ease. Donghua Material Science presents application cases for different fields and conditions for discussion with industry colleagues.
Higher temperature requirements
Where the operating conditions demand even higher temperature resistance, Donghua Material Science offers three temperature classes — DE4068, DE4069 and DE4070 — to be selected flexibly according to actual needs.
| Item | DE4067 | DE4069 | DE4070 |
|---|---|---|---|
| Tg (DMA, °C) | 180 | 251 | 266 |
| Tg (DSC, °C) | 189 | 255 | 279 |
| Part A viscosity (25 °C, cP) | 3,605 | 5,400 | 5,400 |
| Part B viscosity (25 °C, cP) | 125 | 150 | 155 |
| Mixed viscosity (25 °C, cP) | 532 | 735 | 668 |
| Pot life (25 °C, h) | 5 | > 24 | > 24 |
| Gel time (150 °C) | 13'20" | 14'45" | 52' |
| Tensile — strength / modulus / elongation | 70 MPa / 3,000 MPa / 2.82% | 68 MPa / 3,032 MPa / 2.57% | 79.1 MPa / 3,300 MPa / 2.80% |
| Flexural — strength / modulus | 132 MPa / 2,900 MPa | 119 MPa / 3,030 MPa | 117 MPa / 3,190 MPa |
High-temperature pultrusion
| Application | Tg (°C) | Tensile strength (MPa) | Tensile modulus (MPa) | Flexural strength (MPa) | Deflection (mm) |
|---|---|---|---|---|---|
| Pultrusion, Tg > 190 °C | 190–210 | 50–60 | 2,500–3,500 | 100–130 | 6–12 |
| Pultrusion, Tg > 150 °C | 160–170 | 50–60 | 2,500–3,500 | 100–130 | 7–12 |
| Carbon/glass hybrid, high Tg | 175–185 | 65–75 | 3,000–4,000 | 120–130 | 9–11 |

Typical high-temperature insulation applications — reactor support bars, high-temperature insulating rods, resin cable cores and sucker rods — typically achieve Tg of 170–180 °C with compressive strength of 220–250 MPa and compressive modulus of 2,000–2,500 MPa, and pass the tracking test at 2.5 kV for 6 h; compressive strength is maintained after 160 °C × 1 h.
Weatherable, flame-retardant applications
Coastal high salt fog, strong UV, saline-alkali tidal flats, chemical industrial parks — weatherability and flame retardancy have never been an either/or choice. For such high-weatherability, high-flame-retardancy applications, Donghua Material Science offers high-performance solutions.
| Property of the cured resin | Test standard | Typical value |
|---|---|---|
| Tensile strength (MPa) | GB/T 2567-2008 | 45–65 |
| Tensile modulus (MPa) | GB/T 2567-2008 | 3,000–4,500 |
| Elongation at break (%) | GB/T 2567-2008 | 2–3 |
| Flexural strength (MPa) | GB/T 2567-2008 | 70–90 |
| Flexural modulus (MPa) | GB/T 2567-2008 | 3,000–4,000 |
| Impact strength (kJ/m²) | GB/T 2567-2008 | 10–20 |
| Tg (DSC, °C) | IEC 61006 | 140–160 |
| Mechanical retention after DH 1000 h (%) | IEC 61215-2:2016 | > 70 |
| Mechanical retention after UV 2000 h (%) | ISO 4892-2 | > 80 |
| Corresponding composite property | Test standard | Typical value |
|---|---|---|
| Tensile strength T0 (MPa) | ISO 527 | 1,400–1,600 |
| Tensile modulus T0 (GPa) | ISO 527 | 55–65 |
| Tensile strain T0 (%) | ISO 527 | 2.5–3.5 |
| Flexural strength F0 (MPa) | ISO 14125 | 1,300–1,500 |
| Flexural modulus F0 (GPa) | ISO 14125 | 50–60 |
| ILSS (MPa) | ISO 179-1 | 50–60 |
If you are looking for a high-temperature composite solution that is weather-resistant, heat-resistant, corrosion-resistant, insulating and process-friendly, please contact us to discuss it in depth with our technical team. Let solutions based on the cycloaliphatic epoxy resin series become a powerful engine for your next generation of product innovation, and together let us define the future of the industry.
